مدينة الكهرباء
اهلا ومرحبا بكل اعضائنا وزوارنا الكرام فى منتدى مدينه الكهرباء
عليكم الافاده والاستفاده
ولكم منا كل الحب والتقدير
مدينة الكهرباء
اهلا ومرحبا بكل اعضائنا وزوارنا الكرام فى منتدى مدينه الكهرباء
عليكم الافاده والاستفاده
ولكم منا كل الحب والتقدير
مدينة الكهرباء
هل تريد التفاعل مع هذه المساهمة؟ كل ما عليك هو إنشاء حساب جديد ببضع خطوات أو تسجيل الدخول للمتابعة.

مدينة الكهرباء

عالم (الاتصالات والالكترونيات&القوى والات الكهربائيه)
 
الرئيسيةأحدث الصورالتسجيلدخول
نقدم الحلول الكاملة لأنظمة الطاقة و التحكم " دوائر باور / دوائر تحكم / plc / انظمة الحرارة / دوائر تحسين معامل القدرة/ اللوحات الموفرة للطاقة /بادئات الحركة للمحركات / تحكم فى السرعة
اهلا ومرحبا بكل اعضائنا الكرام عليكم الافاده والاستفاده ولكم منا كل الحب والتقدير
اان واجهتك اى مشكله او اردت اى استفسار راسلنى على ايميل(bravewael_1988@yahoo.com)(وائل حلمى)

 

 5 to 30 Minute Timer

اذهب الى الأسفل 
كاتب الموضوعرسالة
وائل حلمى
المدير العام
المدير العام
وائل حلمى


الدوله : مصر
عدد المساهمات : 311
نقاط : 55223
السٌّمعَة : 3
تاريخ التسجيل : 29/04/2009

5 to 30 Minute Timer Empty
مُساهمةموضوع: 5 to 30 Minute Timer   5 to 30 Minute Timer I_icon_minitimeالأربعاء أبريل 21, 2010 4:21 pm

Description
A switched timer for intervals of 5 to 30 minutes incremented in 5 minute steps.

5 to 30 Minute Timer 5_30timer


Notes:
Simple to build, simple to make, nothing too complicated here. However you must use the CMOS type 555 timer designated the 7555, a normal 555 timer will not work here due to the resistor values. Also a low leakage type capacitor must be used for C1, and I would strongly suggest a Tantalum Bead type. Switch 3 adds an extra resistor in series to the timing chain with each rotation, the timing period is defined as :-

Timing = 1.1 C1 x R1

Note that R1 has a value of 8.2M with S3 at position "a" and 49.2M at position "f". This equates to just short of 300 seconds for each position of S3. C1 and R1 through R6 may be changed for different timing periods. The output current from Pin 3 of the timer, is amplified by Q1 and used to drive a relay. The relay contacts give physical and electrical separation and may be used to switch circuits using higher current or voltage. Alternatively if an audible or visual output is desired then the relay may be substituted for a buzzer or LED.

Breadboard Layout:
As a first realisation I made a layout on breadboard. The rotary switch, relay and driver transistor were omitted, the parts being replaced by a single red LED and 2.7k resistor (see below).

5 to 30 Minute Timer 5_30_min
Parts List:
Relay 9 volt coil with c/o contact (1)
S1: On/Off (1)
S2: Start (1)
S3: Range (1)
IC1: 7555 (1)
B1: 9V (1)
C1: 33uF CAP (1)
C2: 100n CAP (1)
C3: 100n CAP (1)
Q1: BC109C NPN (1)
D1: 1N4004 DIODE (1)
R1,R2,R3,R4,R5,R6 : 8.2M RESISTOR (6)
R7: 4.7k RESISTOR (1)
R8: 100k RESISTOR (1)
الرجوع الى أعلى الصفحة اذهب الى الأسفل
https://elmadina.yoo7.com
 
5 to 30 Minute Timer
الرجوع الى أعلى الصفحة 
صفحة 1 من اصل 1
 مواضيع مماثلة
-
» Periodic Timer
» Asymmetric Timer
» 24 Hour Timer

صلاحيات هذا المنتدى:لاتستطيع الرد على المواضيع في هذا المنتدى
مدينة الكهرباء :: المنتديات الهندسية :: قسم المشاريع و الدوائر الالكترونية :: Timing Circuits-
انتقل الى: